محاسبات انواع اتصالات جوش با تصاویر مربوط

[M.A.A.H.R]

Welding Calculations
دوستان سلام اگر این مقاله رو از دست بدید بعدها که مهندس جوش شدید پشیمون میشید پس استفاده کنید

التماس دعا



http://www.gowelding.com/calcs/c1a.gifhttp://www.gowelding.com/calcs/c1b.gifhttp://www.gowelding.com/calcs/c1c.gif
http://www.gowelding.com/calcs/c1d.gif

For more information on Mohrs Circle got to efunda.com (http://www.efunda.com/formulae/solid_mechanics/mat_mechanics/mohr_circle.cfm)

http://www.gowelding.com/calcs/c2a.gif http://www.gowelding.com/calcs/c2b.gif Next Page (http://www.gowelding.com/calcs/c3.html) Menu Page (http://www.gowelding.com/calcs/calc.htm)

[M.A.A.H.R]

Lap Joint
Weld subject to longitudinal shear only http://www.gowelding.com/calcs/c3a.gifhttp://www.gowelding.com/calcs/c3b.gif

[M.A.A.H.R]

Cantilever
Welds Subject to both bending and shear http://www.gowelding.com/calcs/c4.gifhttp://www.gowelding.com/calcs/brace.gif

[M.A.A.H.R]

Lap Joint Subject To Torsion
Welds Subject to both bending and shear http://www.gowelding.com/calcs/c5a.gifhttp://www.gowelding.com/calcs/c5b.gifhttp://www.gowelding.com/calcs/c5c.gif

[M.A.A.H.R]

Rectangular Block Subject To Torsion
In this case Torsion is the same as an applied moment http://www.gowelding.com/calcs/c6c.gifhttp://www.gowelding.com/calcs/c6a.gifhttp://www.gowelding.com/calcs/c6b.gif

[M.A.A.H.R]

T Butt Weld Subject To Torsion
http://www.gowelding.com/calcs/c7a.gifhttp://www.gowelding.com/calcs/c7b.gif

[M.A.A.H.R]

http://www.gowelding.com/calcs/c8.gif Next Page (http://www.gowelding.com/calcs/c9.html) Menu Page (http://www.gowelding.com/calcs/calc.htm)

[M.A.A.H.R]

Lap Joint Subject To Bending and ShearThis is a lap joint with an offset. I could not find a calculation for this in any reference so I put this together. I have assumed that there will be a vertical shear force caused by the offset load creating a moment about the mid point between the welds (marked with the red dot), as well as a horizontal shear force. http://www.gowelding.com/calcs/c9b.gif http://www.gowelding.com/calcs/c9a.gif Alternative approach (http://www.gowelding.com/calcs/lap-joint.pdf) it gives the same answer as my method. My thanks to the person that sent this to me.

[M.A.A.H.R]

http://www.gowelding.com/calcs/c10a.gifhttp://www.gowelding.com/calcs/c10b.gif

[M.A.A.H.R]

Calculating Volume Using Solids Of Revolution
http://www.gowelding.com/calcs/c11a.gif Some Properties of plane areasFIGURECENTROIDMOMENT OF AREAhttp://www.gowelding.com/calcs/cta.gifhttp://www.gowelding.com/calcs/ctb.gifhttp://www.gowelding.com/calcs/ctc.gifhttp://www.gowelding.com/calcs/ctd.gifhttp://www.gowelding.com/calcs/cte.gifhttp://www.gowelding.com/calcs/ctk.gifhttp://www.gowelding.com/calcs/ctf.gifhttp://www.gowelding.com/calcs/ctg.gifhttp://www.gowelding.com/calcs/ctj.gifhttp://www.gowelding.com/calcs/cth.gifhttp://www.gowelding.com/calcs/cti.gif

[Behteshamifar]

سلام
مقاله عالی بود فقط مهندس اگر لطف بفرمائید و PDF این مقاله رو به ایمیل ذیل سند بفرمائید ممنون میشم

Behzad.Ehteshamifar@gmail.com

[M.A.A.H.R]

با سلام در اینترنت سرچ کنیدcalculate weld سایتش میاد